The Spec Of Electronic Contract Manufacturing : 1. The series is specially designed for applications requiring higher brightness.
2. The white LED which was fabricated using a blue LED and a phosphor, and the phosphor is excited by blue light and emits yellow fluorescence. The mixture of blue light and yellow light results in white emission.
3. Utilizing advanced ....
The Spec Of Electronic Contract Manufacturing : 1. Control up to 110 rectifier modules and monitor 4 banks of
batteries in a 24V or 48V DC power system
2. Microprocessor-based front panel with 100 stored alarms
4 digit, 12mm LCD display +/-5% accuracy normally displays output
current and output voltage
3. 16 character, a 2-line alphanumeric LCD d....
The Spec Of Electronic Contract Manufacturing : 1. Model: H1201E, H1202E, H1203E.
2. VA: 20, 20, 20.
3. PRI(VAC): 120, 240, 208 / 240.
The Spec Of Electronic Contract Manufacturing : 1. Ceramic Disk Capacitor & Multi-layer Ceramic Capacitor (Radial).
2. This SPARK GAP is designed for use in protector of CRT circuit and protector of circuit tothe high potential pulse.
3. As this SPARK GAP is a complete sealing type, so in the discharge, a spark does not appear in the outside, a discharge sound doe....
The Spec Of Electronic Contract Manufacturing : TFT LCD-TVs power supplies for 29" to 42" large monitor.
The Spec Of Electronic Contract Manufacturing : 1. 0.8mm board to board male & female (right angle assembly).
2. Height: 6.15mm.
The Spec Of Electronic Contract Manufacturing : Introduction of CR: featuring consistency and stably-controlled, these carbon film resistors with reasonable prices are widely & largely used in the electronic, electrical and information industries.
This resistor is a ceramic bar tightly coated with a carbon film which is composed of carbon separated from organic com....
The Spec Of Electronic Contract Manufacturing : 1. Cup-yoke, back can of automotive and Hi-Fi speaker.
2. Cup-yokes use cold forging production with one piece structure for cost saving.
The Spec Of Electronic Contract Manufacturing : 1. Must be stable electric circuit
2. Positive ploe for red wire, negative pole for black or white wire. ( It won't be spoil when connection is opposite. )
The Spec Of Electronic Contract Manufacturing : Digital 2.4GHZ RF transmitter and receiver modules using GFSK modulation, 3Mbps data rate, up to 15 meters indoor, and 80 meters outdoor.
The Spec Of Electronic Contract Manufacturing : 1. Magnetically shielded and low DC resistance.
2. Ideal for DC-DC converter applications in hand personal computer etc.
3. Available on tape and reel for automatic insertion.
The Spec Of Electronic Contract Manufacturing : 1. With strict Q.C. and strong development ability, our inverter series have achieved CE, e-mark via TUV approval and ISO 9001 certification.
2. All of our inverters are wisdom micro control models and have more better protections than normal inverters.
The Spec Of Electronic Contract Manufacturing : The unit includes everything you need to convert a standard vehicle into an emergency vehicle. Installation is simple- just drill a 1" diameter hole in the existing composite lamp structure and install the strobe bulbs with two screws.
The Spec Of Electronic Contract Manufacturing : 1. LED light panel.
2. Custom size assembling (30 x 30 cm/unit x 1).
3. Super eneragy saving.
The Spec Of Electronic Contract Manufacturing : 1. Complied standards:
(1) UL817 CSA22.2.
(2) NO.21-95.
(3) NEMA 5-15P.
2. Rating: 10/13/15A 125V.
The Spec Of Electronic Contract Manufacturing : 1. Cripm attachment for flexible cable ( right angle plug).
2. 2. Impedance: 50.
The Spec Of Electronic Contract Manufacturing : 1. Application: wooden case, assembly, siding, panel, decking, sheathing, fencing.
1. Shank: smooth, ring, screw.
The Spec Of Electronic Contract Manufacturing : Car audio; stereo wiring harness.
The Spec Of Electronic Contract Manufacturing : 1. Shows different areas.
2. Accessory detecting sensor weak electric.
3. Monitor.
4. Delay timing settings.
5. Could be used with automatic police calling system or the surveillance system.
6. One set of wired sensing circuits.
7. Self activated spare battery to be used when there is a power cut.
8. Wireless se....
The Spec Of Electronic Contract Manufacturing : 1. Description: horizontal type with shaft.
2. Applications: suitable for car-audio, TV, VTR, household applicances, measuring equipment and other consumer or industrial products.
The Spec Of Electronic Contract Manufacturing : 1. Product name: AC axial fan power cord.
2. Fan parts and components.
The Spec Of Electronic Contract Manufacturing : For signal light:
1. For the aforesaid specification, the brightness and other colors can be added according to the chips required by the customer.
2. The LED gel shape is available for change upon the requirement of the customer for changing the size of illumination angle.
3. Normally, this product uses DC current ....
The Spec Of Electronic Contract Manufacturing : Quartz is a device that carries the piezoelectric characteristics. The piezoelectric characteristics of a quartz crystal is briefly explained below: If a piezoelectric quartz crystal has electrodes plated on opposite faces and if a potential is applied between these electrodes, forces will be exerted on the bound charg....
The Spec Of Electronic Contract Manufacturing : 1. Bonded compression molding NdFeB magnets.
2. In a variety of designs and easy to be shaped.
3. Widely used in the communication and computer products such as cellular phone and meter, sensor and spindle motor for CD ROM.
4. Can be magnetized in multipoles.
The Spec Of Electronic Contract Manufacturing : Optical fiber patch cord.
The Spec Of Electronic Contract Manufacturing : 1. Surface mount assembly technology service.
2. SMT assembly.
3. Making SMT for NOKIA, SONY and some other famous companies.
The Spec Of Electronic Contract Manufacturing : 1. Product name: mini MAC VGA adatpors.
2. Hd15 female / db 15 male (hex screw x 2, hex nut x 1).
3. 7 & 10 jumpered together using a 28 gage insulated conductor.
The Spec Of Electronic Contract Manufacturing : 1. Part No.: MR16 - 3512 F x G53 – XXX.
2. 3515 = Lighting source( 4 pcs RED, 4 pcs Green, 4 pcs Blue).
3. X = LED color ( F / color changing ).
4. X = C / cover, N / without cover.
The Spec Of Electronic Contract Manufacturing : 1. BNC connector.
2. BNC "U" link monitor.
3. Two plug/one jack with one bead-chain protector for monitor usage.
The Spec Of Electronic Contract Manufacturing : 1.Axial type (1.7mm lamp).
2.Emitted color: red.
3.Resin color: water clear.
