The Spec Of Engraving Equipment : I. MITSUBISHI high-level control system
1. Three-axis, low-inertia, high-torque motor to do three-axis control, three-axis simultaneous engraving and milling.
2. Ultimate PLC human machine interface detect and display each warning message.
II. 24000RPM built-in high-speed spindle, high-rigidity, high-speed design, w....
The Spec Of Engraving Equipment : 1. Mehanite cast.
2. Taiwan spindle and leading screw, Japan servo motor.
3. Every machine is checked by Renishaw laser and ball bar.
4. Control system: Fanuc, Mitsubishi.
5. High speed spindle. 1. Table size: 550 x 480mm.
2. Travel: 450 x 500 x 235mm.
3. Distance from spindle to table: 55 - 290mm.
4. Rotati....
The Spec Of Engraving Equipment : 1. Standard accessories: half-canopied canopy, tool cooling system, auto-grease system, heat-exchanger, RS232 connection line, spindle cooling system, collect holder, collect, lamp, tool set.
2. Extra accessories: full-canopied canopy, high-speed spindle, 4th Axis, auto tool compensate system, air dryer. 1. Work t....
The Spec Of Engraving Equipment : Three-axis servomotors are directly coupled to the ball screws, ensuring the least backlash and high-precision performance Special lubricating circuit ensures even lubrication. Pressure-discharge oil distributor also ensures that each oil injection spot of the slide surfaces receives equal volume of oil, with no waste ....
The Spec Of Engraving Equipment : 1. Standard accessories: Half-canopied canopy, tool cooling system, auto-grease system, heat-exchanger, RS232 connection line, spindle cooling system, collect holder, collect, lamp, tool set.
2. Extra accessories: full-canopied canopy, high-speed spindle, 4th axis, auto tool compensate system, air dryer. 1. Work t....
The Spec Of Engraving Equipment : 1. Standard accessories: half-canopied canopy, tool cooling system, auto-grease system, heat-exchanger, RS232 connection line, spindle cooling system, collect, lamp, tool set.
2. Extra accessories: high-speed spindle, auto tool compensate system, air dryer. 1. Stroke of X axis: 3000 mm. 2. Stroke of Z axis: 400 mm....
The Spec Of Engraving Equipment : 3 dimensional pantograph engraver. 1. Motor: 0.7 K.W. 2. Voltage: 220/60/3PH V/HZ. 3. Speed ( pole-changing ): 1700/3400 r.p.m. 4. Engraving spindle speed: 600-20000 r.p.m. 5. Engraving spindle adjustment: 28 speeds step. 6. Engraving spindle rapid lift: 5 mm. 7. Engraving spindle down feed for engraving: 7 mm. 8. ....
The Spec Of Engraving Equipment : 3 dimensional pantograph engraver. 1. Motor: 0.7 K.W. 2. Voltage: 220/60/3PH V/HZ. 3. Speed ( pole-changing ): 1700/3400 r.p.m. 4. Engraving spindle speed: 600-20000 r.p.m. 5. Engraving spindle adjustment: 28 speeds step. 6. Engraving spindle rapid lift: 5 mm. 7. Engraving spindle down feed for engraving: 7 mm. 8. ....
The Spec Of Engraving Equipment : 2 dimensional pantograph engraver. Working table: 1. Clamping area: 560 x 300 mm. 2. Longitudinal travel: 300 mm. 3. Transverse travel: 240 mm. 4. Vertical travel: 300 mm. 5. Max. distance between cutter and worktable and cutter: 300 mm. Template table: 1. Clamping area: 560x400 mm. 2. Max. permissible thickness, o....
The Spec Of Engraving Equipment : 1. Standard accessories: Half-canopied canopy, tool cooling system, auto-grease system, heat-exchanger, RS232 connection line, spindle cooling system, collect holder, collet, lamp, tool set.
2. Extra accessories: Full-canopied canopy, high-speed spindle, 4th Axis, auto tool compensates system, air-dryer. 1. Work t....
The Spec Of Engraving Equipment : Thanks to its robust construct with precision pre-load bearing by MICHAELLIN model 55N and 55 provides a heavy cuts as well as delicate finishing operation.
In addition to particular rations, the Vernier micrometer adjustment offers linear scales accurately set on a intermediate ratio.
Many accessories can be supplie....
The Spec Of Engraving Equipment : 1. It could be utilized in 3D, 2D,cylindrical and concave, protrusion graphic design and symbol engraving, as well as variety of curved, cast-shadow engraving.
2. It is adaptable to develop various of small and precision mold, such as commemorative plaques, name plates, watches and clocks, electrolysis, pen engraving,....
The Spec Of Engraving Equipment : 1. It could be utilized in convave, protrusion graphic design and symbol engraving for surface of roller.
2. High-rigidity structure, allowing high-speed and great-precision engraving.
3. Multi-functioned CAD/CAM program that can using scanner and can address multi-axial for concurrent processing 1. Diameter of....
The Spec Of Engraving Equipment : 1. Supports commercial purposes.Applications: chops, plaques, relief, carvings, decorations, and giftware.
2. Widely applied for treating: ABS, acrylic resin, Bakelite, wax, aluminum, brass, and steel. 1. Work table: 420 × 320 mm. 2. Load of work table: 50 kg. 3. Stroke of x axis:400 mm. 4. Stroke of y axis:....
The Spec Of Engraving Equipment : Multi-functioned CAD/CAM program that can using scanner and can address multi-axial for concurrent processing. 1. Stroke of x axis: 3000 mm. 2. Stroke of z axis: 400 mm. 3. Max. siameter of table: o600mm. 4. Center to table: 320 mm. 5. Spindle to table: 400 mm. 6. Spindle motor: high-frequency motor. 7. Spindle pow....
The Spec Of Engraving Equipment : 1. Multi-functioned CAD/CAM program that can using scanner and can address multi-axial for concurrent processing.
2. It is adaptable to develop various of medium and precision mold, such as molds of shoes, car light, plastic injection, press & pills forming. 1. Work table 1000 ×800 mm. 2. Load of work t....
The Spec Of Engraving Equipment : 1. The multi-functioned CAD/CAM program applied will be compatible
with the scanner and digitizing board peripheral devices. The synchronal multi-spindle design specified in mass production is
also available.
2. It is adaptable to develop small size and precision mold, such as badge, nameplate, watch, electrode, p....
The Spec Of Engraving Equipment : 1. It is adaptable to develop small size and precision mold, such as
badge, nameplate, watch, electrode, pen sleeve,
zipper and so on.
2. The multi-functioned CAD/CAM program applied will be compatible
with the scanner and digitizing board peripheral devices. The
synchronal multi-spindle design spe....
The Spec Of Engraving Equipment : 1.MITSUBISHI high-level control system
a.Three-axis, low-inertia, high-torque motor to do three-axis control, three-axis simultaneous engraving and milling
b.Ultimate PLC human machine interface detect and display each warning message
c.24000RPM built-in high-speed spindle, high-rigidity, high-speed design, with ....
The Spec Of Engraving Equipment : 1.MITSUBISHI high-level control system
a.Three-axis, low-inertia, high-torque motor to do three-axis control, three-axis simultaneous engraving and milling
b.Ultimate PLC human machine interface detect and display each warning message
c.24000RPM built-in high-speed spindle, high-rigidity, high-speed design, with ....
The Spec Of Engraving Equipment : 1.MITSUBISHI high-level control system
a.Three-axis, low-inertia, high-torque motor to do three-axis control, three-axis simultaneous engraving and milling
b.Ultimate PLC human machine interface detect and display each warning message
c024000RPM built-in high-speed spindle, high-rigidity, high-speed design, with ....
The Spec Of Engraving Equipment : 1.MITSUBISHI high-level control system
a.Three-axis, low-inertia, high-torque motor to do three-axis control, three-axis simultaneous engraving and milling
b.Ultimate PLC human machine interface detect and display each warning message
c024000RPM built-in high-speed spindle, high-rigidity, high-speed design, with ....
The Spec Of Engraving Equipment : 1.MITSUBISHI high-level control system
a.Three-axis, low-inertia, high-torque motor to do three-axis control, three-axis simultaneous engraving and milling
b.Ultimate PLC human machine interface detect and display each warning message
c024000RPM built-in high-speed spindle, high-rigidity, high-speed design, with ....
The Spec Of Engraving Equipment : 1. High-rigidity machine construction X, Y, and Z axes are protected with steel telescopic covers Three-axis ball screws.
2. Table size: 400x250 mm.
3. Travel (X-Y-Z Axis): 200/150/300mm. Table: 1. Table size: 400x250 mm. 2. T slots (NO .x W x CD): 3x12x70 mm. 3. Table load (Max.): 120kg. Travel: 1. X-Axis: 200mm....
The Spec Of Engraving Equipment : 1. Three-axis servomotors are directly coupled to the ball screws、ensuring the least backlash and high-precision performance Special lubricating circuit ensures even lubrication. Pressure-discharge oil distributor also ensures that each oil injection spot of the slide surfaces receives equal volume of oil、with no w....
The Spec Of Engraving Equipment : 1. Power supply AC adaptor.
2. Machine size: 140(L) x 25(W)mm.
3. RPM: 18000-20000. 1. Function: engraves any surface. 2. Power supply: AC adaptor. 3. Machine size: 140(L) x 25(W)mm. 4. Machine weight: 0.359kgs. 5. Body material: ABS. 6. RPM: 18000-20000. 7. Accessories: with 1 tips. 8. Packing: blister card in....
The Spec Of Engraving Equipment : 1. Power supply AC adaptor.
2. Machine size: 140(L) x 25(W)mm.
3. RPM: 18000-20000. 1. Function: engraves any surface. 2. Power supply: AC odaptor. 3. Machine size: 140(L) x 25(W) mm. 4. Machine weight: 0.36kgs. 5. Body material: ABS. 6. RPM: 18000-20000. 7. Accessories: with 7 tips. 8. Packing: blister + card ....
The Spec Of Engraving Equipment : 1. Power supply: 4 size AA bateries.
2. Machine size: 140(L) x 25(W)mm.
3. RPM: 16000-18000. 1. Function: engraves any surface. 2. Power supply: 4 size AA bateries. 3. Machine size: 140(L) x 25(W)mm. 4. Machine weight: 0.135kgs. 5. Body material: ABS. 6. RPM: 16000-18000. 7. Accessories: with 1 tips. 8. Packing....
The Spec Of Engraving Equipment : 1. Power supply: AC operated.
2. Machine size: 195(L) x 50(W)mm.
3. RPM: 16000-18000. 1. Function: engraver. 2. Power supply: AC adaptor. 3. Machine size: 195(L) x 50(W)mm. 4. Machine weight: 0.355 kgs. 5. Body material: ABS. 6. RPM: 16000-18000. 7. Torsion: 400 g.cm. 8. Accessories: 1 bolt. 9. Packing: kraft b....
The Spec Of Engraving Equipment : 1. Power supply: AC adaptor.
2. Machine size: 225(L) x 38(W) mm.
3. Machine weight: 1.493 kgs.
4. RPM: 2000-12000. 1. Function: engraver. 2. Power supply: AC adaptor. 3. Machine size: 225(L) x 38(W)mm. 4. Machine weight: 1.493 kgs. 5. Body material: ABS. 6. RPM: 2000-12000. 7. Accessories: total: 49 pcs. 8. P....
