The Spec Of Ballasts : Toroidal electromagnetic ballast. Toroidal Electromagnetic Ballast.
55*25-55*29. ....
The Spec Of Ballasts : Electronic ballast is a device that limiting the amount of current flowing in an electric circuit. It also provides proper starting and operating electrical condition to power one or more florescent lamps. 1. Use electronic circuit design, 30% less power consumption than coil ballast. 2. Rapid start, no need of sta....
The Spec Of Ballasts : 1. Slim case, easy to set in fixtures.
2. Low temperature raise.
3. Active power factor control.
4. Preheat warm start of lamp.
5. High power factor value > 0.98.
6. Low THD < 10%.
7. ON/OFF switching test > 20,000 times.
8. Safety protection for short circuit and open circuit.
9. High operating frequency and N....
The Spec Of Ballasts : 1. Last phase turn-off protection of light tubes.
2. Short circuit protection.
3. When the heated tube restarts, the electronic ballast will automatically light up every one minute. If light start is unsuccessful after 15 minutes, the ballast will automatically turn off for protection. (restart power supply.) 1....
The Spec Of Ballasts : 1. OKES ballasts are more stable, quick start, long-life, high power factor, no noice and effective energy saving.
2. Design for variou fluorescent lamps, inset install ceiling lamps, spot lights etc. MK-4B-2:
1. FOR T8, one ballast for two lamp.
2. Volage: 220V 50Hz.
3. Power: 18W, 36W.
4. PF: 0.98, BF: 0....
The Spec Of Ballasts : 1. Volt/fre.(V/hZ): 12V DC.
2. Watt(W): FL20W x 1.
3. Input current(A): 1.6. 1. Dimension(mm):
(1) a: 147.
(2) b: 132.
(3) c: 115.
2. Weight(kg): 0.34. ....
The Spec Of Ballasts : 1. We devoted ourselves in researching and developing DC electronic ballast for years.
2. Manufacture by experienced and professional teamwork. Always support our customer energy-saving, stable, full-range electronic products. By our constant efforts, we make all kinds of DC electronic ballast toward market demand. W....
The Spec Of Ballasts : 1. Input voltage(V): 110.
2. Input electric current(A): 0.32/0.34.
3. Input power(W): 36/38.
4. Power factor(%): 99.
5. Lighting frequency(Hz): 49±1.
6. Total harmonic distortion(%): ＜20. 1. Suitable fluorescent tubes: FL/36/40W.
2. Quantity: 1. ....
The Spec Of Ballasts : 1. Electronic ballast that makes electronic devices more stable.
2. Electronic ballast is an electrical component that makes fluorescent lamp work in high performance. Electronic ballast can generate less heat than electro-magnetic ballast; therefore, the lifespan of electronic ballasts are also longer than electro-ma....
The Spec Of Ballasts : 1. Lamp: 14w x 2 / parallel.
2. Pre-heat start.
3. The voltage change permit range: +/-10%. 1. Housing dimension: 316 x 40 x 30 mm (LxWxH).2. Input voltage: 110~220V.3. Input current: 0.256~0.128A.4. P.F.: 110V>99%; 220V>97%.5. CNS13755 approval. ....
The Spec Of Ballasts : 1. Features:
(1) High relible long life, no damage after 8000 times startings.
(2) Saving energy above 30%.
(3) No flashing, steady output power, high output lumin.
(4) High power factor, perfect function.
2. Applied for: lighting for supermarket, housing, hotel, office etc. Specifications:1. Technical specifi....
The Spec Of Ballasts : Certified with CNS 13755 and registered for authentication by Bureau of Standards, Metrology and Inspection ,MOEA.
CNS 14115 EMI specification compliant.
The Spec Of Ballasts : Certified with CNS 13755 and registered for authentication by Bureau of Standards, Metrology and Inspection ,MOEA.
CNS 14115 EMI specification compliant.
The Spec Of Ballasts : Certified with CNS 13755 and registered for authentication by Bureau of Standards, Metrology and Inspection ,MOEA.
CNS 14115 EMI specification compliant.
The Spec Of Ballasts : 1.HID Electronic Ballast (CDM-T, HQI-T, MHN-T, HCI-T, NAV-T light tube suitable）
2.Certified with CNS 13755 and registered for authentication by Bureau of Standards, Metrology and Inspection ,MOEA.
CNS 14115 EMI specification compliant.
The Spec Of Ballasts : 1. Lamp: 14w x 1 / series & parallel.
2. Pre-heat start.
3. The voltage change permit range: +/-10%. 1. Housing dimension: 316 x 40 x 30 mm (LxWxH).2. Input voltage: 110~220V.3. Input current: 0.41~0.2A.4. P.F.: 110V>99%; 220V>98%.5. CNS13755 approval. ....
The Spec Of Ballasts : 1. Lamp: 14Wx 1/series& parallel.
2. Pre-heat start.
3. The voltage change permit range: +/-10%.
4. Input voltage: 110~220V.
5. Input current: 0.484~0.242A.
6. P.F.: 110V>99%; 220V>99%.
7. CNS13755 approvaled. 1. Housing dimention(mm): 316(L)x 40(W)x 30(H).2. Input voltage: 110~220V.3. Input current....
The Spec Of Ballasts : 1. Lamp: 14Wx 1/ PARALLEL.
2. Pre-heat start.
3. The voltage change permit range: +/-10%.
4. Input voltage: 110~220V.
5. Input current: 0.15~0.08A.
6. P.F.: 110V>99%; 220V>97%.
7. CNS13755 approvaled. 1. Housing demention(mm): 316(L)x 40(W)x 30(H).2. Input voltage: 110~220V.3. Input current: 0.15~0.08A.....
The Spec Of Ballasts : 1. Protection function of electronic starter:
(1) Over-current protection.
(2) No-load protection.(power consumption at no-load is less than 1W).
(3) A florescent tube malfunction protection.
2.safety requirement and reliability based:
(1)Definition: the electronic starter fail to lid the lamp indicate the end of ....
The Spec Of Ballasts : 1. Protection function of electronic starter:
(1) Over-current protection.
(2) No-load protection.(power consumption at no-load is less than 1W).
(3) A florescent tube malfunction protection.
2.safety requirement and reliability based:
(1)Definition: the electronic starter fail to lid the lamp indicate the end of ....
The Spec Of Ballasts : 1. Protection function of electronic starter:
(1) Over-current protection.
(2) No-load protection.(power consumption at no-load is less than 1W).
(3) A florescent tube malfunction protection.
2.safety requirement and reliability based:
(1)Definition: the electronic starter fail to lid the lamp indicate the end of ....
The Spec Of Ballasts : 1. Protection function of electronic starter:
(1) Over-current protection.
(2) No-load protection.(power consumption at no-load is less than 1W).
(3) A florescent tube malfunction protection.
2.safety requirement and reliability based:
(1)Definition: the electronic starter fail to lid the lamp indicate the end of ....
The Spec Of Ballasts : 1. Protection function of electronic starter:
(1) Over-current protection.
(2) No-load protection.(power consumption at no-load is less than 1W).
(3) A florescent tube malfunction protection.
2.safety requirement and reliability based:
(1)Definition: the electronic starter fail to lid the lamp indicate the end of ....
The Spec Of Ballasts : 1. Protection function of electronic starter:
(1) Over-current protection.
(2) No-load protection.(power consumption at no-load is less than 1W).
(3) A florescent tube malfunction protection.
2.safety requirement and reliability based:
(1)Definition: the electronic starter fail to lid the lamp indicate the end of ....
The Spec Of Ballasts : 1. Protection function of electronic starter:
(1) Over-current protection.
(2) No-load protection.(power consumption at no-load is less than 1W).
(3) A florescent tube malfunction protection.
2.safety requirement and reliability based:
(1)Definition: the electronic starter fail to lid the lamp indicate the end of ....
The Spec Of Ballasts : 1. Protection function of electronic starter:
(1) Over-current protection.
(2) No-load protection.(power consumption at no-load is less than 1W).
(3) A florescent tube malfunction protection.
2.safety requirement and reliability based:
(1)Definition: the electronic starter fail to lid the lamp indicate the end of ....
The Spec Of Ballasts : 1. Protection function of electronic starter:
(1) Over-current protection.
(2) No-load protection.(power consumption at no-load is less than 1W).
(3) A florescent tube malfunction protection.
2.safety requirement and reliability based:
(1)Definition: the electronic starter fail to lid the lamp indicate the end of ....
The Spec Of Ballasts : 1. Protection function of electronic starter:
(1) Over-current protection.
(2) No-load protection.(power consumption at no-load is less than 1W).
(3) A florescent tube malfunction protection.
2.safety requirement and reliability based:
(1)Definition: the electronic starter fail to lid the lamp indicate the end of ....
The Spec Of Ballasts : 1. Protection function of electronic starter:
(1) Over-current protection.
(2) No-load protection.(power consumption at no-load is less than 1W).
(3) A florescent tube malfunction protection.
2.safety requirement and reliability based:
(1)Definition: the electronic starter fail to lid the lamp indicate the end of ....
The Spec Of Ballasts : 1. Protection function of electronic starter:
(1) Over-current protection.
(2) No-load protection.(power consumption at no-load is less than 1W).
(3) A florescent tube malfunction protection.
2.safety requirement and reliability based:
(1)Definition: the electronic starter fail to lid the lamp indicate the end of ....
