The Spec Of Can Making Machines : 1. Big cutter shaft adopted to ensure strip dimension and squarness, 90 mm dia. for B1A, 100 mm dia. for B1B.
2. Simple design, easy maintenance and changeover for different can sizes. Equipped with mechanical clampling system for cutter hubs. Carbide cutters available on request.
3. Special thin cutter hub for nar....
The Spec Of Can Making Machines : S-B47A Automatic Vertical Triple Necker with Flanger with vertical design is easily linked and work together with automatic double seamer. Can cylinder is carried by a timing screw and a turret. Triple neck is formed due to guidance from three shaped outer necking die made of tungsten carbide. Proper inner die is to pr....
The Spec Of Can Making Machines : S-B55 Automatic Vertical Flanger with Beader with vertical design is easily linked and work together with automatic double seamer. Can cylinder is carried by a timing screw and a turret to let swing flanging die (or spin flanging die) form flange. Then , flanged can body is transferred by a turret to let beading roller....
The Spec Of Can Making Machines : S-B10A Automatic Lining- Drying Machine is specially designed for small round end. Curled end is separated by a pair of separating knives at end magazine ;then feeding bars send it to lining station. End is lifted up by a turning chuck. A mechanical gun (or electronic gun) undertake the lining task to evenly spray comp....
The Spec Of Can Making Machines : S-B63 Automatic Lining Machine is specially designed for small round end. Curled end is separated by a pair of separating knives at end magazine ;then feeding bars send it to lining station. End is lifted up by a turning chuck. Four sets of electronic gun undertake the lining task to evenly spray compound along the end....
The Spec Of Can Making Machines : S-B10AL2 Automatic End Counter and Stacker is specially designed for big round end and is recommended to link with one set of lining/drying machine S-B10AL. Dried ends are guided by a chute to reach the inlet magnetic conveyor then enter collection channel. A pair of separating plate and a sensor undertake counting and....
The Spec Of Can Making Machines : S-B24A Automatic Scoring Machine is designed for can body blank scoring. Blanks are stacked on the feeding magazine, and separated by a tiny gear rail and air blowing. An procating
feeding finger push each blank into scoring station, blank is carried forward by turning rollers pressing. A pair of scoring cutters mark ....
The Spec Of Can Making Machines : S-B25S Automatic Can Body Separator horizontal design. Sored can cylinder is carried by a timing screw and a turret. Inner cutter shaft enter can inside and carry cans forward to meet an arc outer rail blade. Cutter edge squeeze the scoring line to separate the can cylinder. Separated can cylinders exit by two individu....
The Spec Of Can Making Machines : S-B31 Automatic Necker with horizontal design. Can cylinder is carried by a timing screw and a turret. Neck is formed due to guidance from a shaped outer necking die made of ungsten carbide. Proper inner die is to prevent wrinkle. With entralized
greasing system and multiple safety devices, easy for enance and can siz....
The Spec Of Can Making Machines : S-B17VBS Automatic Vertical Beading Machine is specially designed to make a single bead on the two piece can body wall near can bottom. Trimmed can body (open side face down) is carried by a timing screw and a turret to let beading roller enter can inside. Bead cluster is created due to pressing between a beading rolle....
The Spec Of Can Making Machines : S-B26A(B) Automatic Scroll Shear is designed for zig zag shape strip cutting and is recommended to link with Automatic Sheet Feeder S-B23B. Sheet is sent to feeding table, guided by flexible roller side guide (or straight side guide). Two sets of round cutters trim two sheet sides . Trimmed sheet is precisely fed forwa....
The Spec Of Can Making Machines : S-B31V(H)Automatic Vertical Can Body Necker with vertical design is easily linked and work together with automatic flanger. Can cylinder is carried by a timing screw and a turret. Neck is formed due to guidance from a shaped outer necking die made of tungsten carbide. Proper inner die is to prevent wrinkle. With recycl....
The Spec Of Can Making Machines : S-B57L Vertical Air Tester is specially designed for big round can. With special detection elements to get an excellent detecting performance, even small pinhole can be detected easily. Empty can is lifted up by air cylinder to let a plug enter can to occupy some can inside volume then fill compressed air into can. Cer....
The Spec Of Can Making Machines : S-B57P Vertical Air Tester is specially designed for aerosol can. With special detection elements to get an excellent detecting performance, even small pinhole can be detected easily. Empty can is lifted up by air cylinder to enter upper detection sleeve then fill high compressed air into can. Certain time later, an el....
The Spec Of Can Making Machines : S-B7A Air Tester is specially designed for round can. With special detection elements to get an excellent detecting performance, even small pinhole can be detected easily. Empty can is carried into by a timing screw and a turret. Pressing plate push can into a rubber set to fix can, then fill compressed air into can. C....
The Spec Of Can Making Machines : 1. Strips lifting by hydraulic cylinder and use proximity switch for strips height control.
2. With duplex switch for machine starting, safe and reliable.
3. With Air Clutch for power transmission, effective but low maintenance.
4. Multi-safety design for machine and personnel safety.
5. Easy for can size chang....
The Spec Of Can Making Machines : S-C5S Automatic Marker is specially designed for non-round end embossing. Curled end is separated by a pair of separating knives at end magazine; then feeding bars send it to marking station. End is marked by a pair of rotating making die. Marked ends are transferred by feeding bars to the collection tray at exit. Simp....
The Spec Of Can Making Machines : 1. Can connect with conveyor to auto press to reduce labor cost.
2. With mechanical clutch actuating, effective but low maintenance.
3. Multi-safety design for machine and personnel safety.
4. Easy for can size changeover and adjust.
5. Perfect products and built for long life, satisfy the requirement of can ma....
The Spec Of Can Making Machines : 1. Machine type: S-A3.
2. Tin plate size: 480 x 900 x 0.15-0.4mm.
3. Capacity per min: up to 30 CPM.
4. Main motor: 1/2HP x 1. 1. Floor space overall height: 1120 x 510 x 1020 mm.2. Net weight: 200 kg. ....
The Spec Of Can Making Machines : 1. Machine type: S-A6.
2. Range of can dia.: 202 - 401D.
3. Range of can height: 48 - 125mm.
4. Capacity per min.: Up to 200 CPM. 1. Main motor: 1HP x 1.2. Floor space overall height: 1630 x 1060 x 1360 mm.3. Net weight: 550 kg. ....
The Spec Of Can Making Machines : S-C87 Automatic Irregular Can Clincher is specially designed for irregular can clinching. Filled can is fed forward through a timing screw and a turret to meet with end. Clinching chuck and two clinching rollers push food down and clip end and can body together at two points. Clinched can is carried out by a turret and....
The Spec Of Can Making Machines : S-B18-2(M) Automatic Strip Feeder is to link with press for end stamping or can body drawing. Strip piled pallet is to be sent into lower roller table. Rollers on the table ,driven by a motor, turn and carry the pallet forward. Forks lift strip stack up and gradually lift up. Three suction pads suck strip up one by one....
The Spec Of Can Making Machines : S-B110 Automatic Transfer Press specially designed to produce aerosol top end, spray lid and threaded oil end. It can be built for single lane or double lanes depending on end size. Max.number of the tooling can be 9 stations for each lane. Capacity can be 100~150 strokes per minute. Therefore, max.capacity can reach 3....
The Spec Of Can Making Machines : S-D21 Automatic Twist-Off Cap Pre-Curler is designed for the cap fringe inward tiny curl. Cap shells, made by press, are lifted up by an elevator and guided to enter the machine via a chute. Six sets of inner curling rollers enter cap inside and carry caps travel along an arc outer curling mold to slightly curl the cap....
The Spec Of Can Making Machines : S-B10RP Automatic F.O.E Repair- Drying Machine is specially designed for small tin round full open end. Curled end is separated by a pair of separating knives at end magazine ; then feeding bars send it to spraying station. End is lifted up by a turning chuck. A NORDSON spraying gun undertake the spraying task to evenl....
The Spec Of Can Making Machines : 1. Easy for maintenance and adjustment.
2. Multi-safety design to insure machine and personnel safety.
3. Roller table use drive reducer suitable for one operator serves
multi feeders.
4. Tinplate (or aluminum) sheet is carry up by three suction pads, three vacuum generators are equipped.
5. Several magnet sep....
The Spec Of Can Making Machines : S-B91 Automatic CNC sheet feeding scroll shear equipped with three axis synchronized movement is suitable for tin or aluminum pre-scrolled sheet secondary scroll cutting. Reliable linear servo motors, electronic cam control system are incorporated. Programmable integrated sheet take-over system can get precise sheet fe....
The Spec Of Can Making Machines : 1. Suitable for home canning.
2. With one 1st and one 2nd seaming rollers.
3. Rollers and cluck are made from alloy steel and harden treatment.
4. Perfect product and built for long lift.
5. Filled can is lifted up to touch chuck by lifter plate through a foot pedal step. 1. Machine type: S-C17V. 2. Range o....
The Spec Of Can Making Machines : S-B15A(H)Automatic 6H Seamer is specially designed for round empty can closing. Flanged can is fed forward through a timing screw and a chain to enter seaming station equipped with 6 sets of seaming spindle. Turning lifter plate lift can up to meet with end . Two seaming rollers undertake seaming operation. Cam driven ....
The Spec Of Can Making Machines : 1. Very sturdy manufacturing of machine flames suitable for round containers making.
2. Rolls and chuck are made from alloy steel and harden treatment.
3. Perfect products and built for long life.
4. With air cylinder for clutch actuating, effective but low maintenance.
5. Easy adjustment and quick for can size....
