The Spec Of Automatic Drilling Machines : 1.5 Banks parameter data, Each set can save various machining parameters. Available to expand to 10 sets(optional).
2.Parameter data can be finely adjusted and is suited for a range of machining operations. The unit can also use preset parameter data for easy operation.
3.EDP function:point sparking(surface sparking)....
The Spec Of Automatic Drilling Machines : * 10 seconds to grind a precise drill for an expert.
* Eay to operate, no experience required for grind a precise drill.
The Spec Of Automatic Drilling Machines : 1.Standard spindle speeds 8000 rpm
2.Optional spindle speeds 12000 rpm
3.Rigid tapping 3000 rpm
4.Spindle nose taper BT40
5.3 axes rapid traverse X, Y, Z: 36 / 36 / 36 m/min
6.Fully enclosed heat isolated electric cabinet
7.High speed mechanical ATC system T-T: M 2.2 sec F 3.2 sec
The Spec Of Automatic Drilling Machines : 1. Spindle gear 12 steps transmission for higher load capacity. High stiffness, high torque design.
2. Machine base is tempered, slide face is treated by high frequency HRC53°
3. High pressure pump, centerized lubrication, better cooling result and increase cutting efficiency.
4. Applicable for various steel workin....
The Spec Of Automatic Drilling Machines : 1.Conveniently to mount on twist drill or hole cutter for automatic drilling and Center-free drilling..
2.Adjusting wheel of cutting force control device can be used for regulating the force of cutting. Therefore, the cutting force for twist drill and hole cutter can be adjusted as you need.
3.Automatic step feed dev....
The Spec Of Automatic Drilling Machines : This drilling machine is designed to drill back center hole. This machine is easy and simple to operate. This center hole is critical for coming and following machining. 1. Spindle Motor:0.5HP 2. Spindle Type:Pneumatic drilling head 3. Stroke:Max. 80mm 4. Work Size:Max. 200mm 5. Drill Size:Max. φ5 mm 6. Feeding....
The Spec Of Automatic Drilling Machines : 1. Available for milling, drilling, & tapping etc.
2. Seel plate machine stand & chip tray.
3. Z-axis manual memory feed.
4. Geared head can be tilted 90° R & L each. 1. Drilling capacity: cast iron: 40mm (1 9/6"), steel: 32mm (1 1/4"). 2. Face milling capacity: 102mm. 3. End milling capac....
The Spec Of Automatic Drilling Machines : 1. Automatic drilling operation allows for equal or unequal hole distance
2. PLC control
3. Touch - sensing screen
4. Allows for a selection of manual or automatic drilling mode
5. Forced oil mist lubrication 1. Automatic drilling operation allows for equal or unequal hole distance. 2. Allows for multip....
The Spec Of Automatic Drilling Machines : • The Column type Deep hole drilling machine with CNC control are designed for drilling waterlines, Ejector pin holes of large type injection molds.
• Spindle is supported by angular contact bearings well-lubricated to all running points in the head.
• The rigid honeycomb walled column gives a stable cutting ....
The Spec Of Automatic Drilling Machines : Our drilling machines have over 10 patents. Their drilling-speed is the fastest in Taiwan. No other brand can overtake on the most convenience and the shortest preparing time. The drilling speed is over 20% from other brand. The really two independent spindle machine – TACO series – can save you more space and more....
The Spec Of Automatic Drilling Machines : 1. The drilling of water holes,electric-heating pipe holes.
2. The drilling of valves,controlling units, pushing rods, and pumps.
3. For automative parts industry, aerospace industry, and electric engineering industry. 1. Drilling diameter range: 6-32 mm.2. Drilling depth: 1800 mm.3. X-axis travel: 2500 mm.4. Y-a....
The Spec Of Automatic Drilling Machines : Our machine is solid for long time using, the operation and adjustment are easy and machine is powerful. We choose the best material and heat treatment, plus well-designed machine structure to achieve machine precise and long-life time. If you need further information about our Tube/Pipe Drilling machine, please vi....
The Spec Of Automatic Drilling Machines : 1. This machine is specially designed for drilling both ends of workpieces.
2. This machine is driven by hydraulic system. Loading, drilling and unloading the workpieces are full-automatic operation.
3. The rotation of drilling-head is driven by motor. The rotary speed can be changed if need.
4. The drilling-head is....
The Spec Of Automatic Drilling Machines : 1. Automatic loading bicycle axis two end drill tapping machine.
2. Strict quality control, best performance, superior quality, complete range of models, simple and easy maintenance, long service life, high reliability. According to cutomer's designs and specifications. Please Contact Us.We shall proceed your requ....
The Spec Of Automatic Drilling Machines : 1.CNC high precision of positioning.
2.Multi-language operation panel, Big size of LCD display, memory for multi-presetting.
3.Intelligent operation system, Auto routing with X-Y axis input.
4.High pitch of ball screw for fast moving Fool of wrong X-Y axis input.
5.Instant Drilling speed to prevent hole edge rippi....
The Spec Of Automatic Drilling Machines : 1. Throat depth: 120 mm.
2. Drilling diameter: 3-10 mm.
3. Minimum distance between holes: 40 mm.
4. Maximum distance between holes: 260 mm.
5. Motor: 1/2 HP x 2, 1 HP. 1. Machine dimensions (L x W x H): 950 x 820 x 1550 mm.2. Net weight: 450 kgs.3. Gross weight: 580 kgs. ....
The Spec Of Automatic Drilling Machines : Engine type: 2 cycle, single cylinder, forced air-cooled, gasoline engine. 1. Displacement: 36 c.c.
2. Horse power: 1.9 HP / 6500 R.P.M.
3. Carburetor: suction type.
4. Ignition system: electronic CDI.
5. Spark plug: champion CJ8.
6. Fuel mixture (petrol): mixed fuel of gasoline and 2 cycle oil at 25:1.
7. Fu....
The Spec Of Automatic Drilling Machines : 1.Power motor for professional drilling use.
2.Built overload circuit clutch system to protect the core bits form getting stuck during drilling. It can be adjusted from outside of gear case.
3.Feeding handle insulation to prevent from electric shock caused by carelessly drilling electric cable or power source.
4.Ove....
The Spec Of Automatic Drilling Machines : OEM/ODM MANUFACTURER
PLASTICS PRODUCTS FOR DIG WELL
SPECIAL PLASTIC PRODUCTS FOR AGRICULTURE/PISCECULTURE
SPECIAL PLASTICS PRODUCTS FOR CONSTRUCTION, HILLSLOPE
OEM/ODM MANUFACTURER AND SUPPLIER
VARITIES OF PLASTIC DERIILING PRODUCTS FOR AGRICULTURE & INDUSTRIAL FIELDS
SPECIAL DRILLING PLASTIC PRODUCTS FOR DIG....
The Spec Of Automatic Drilling Machines : *With circuit protection of breaking for motor, once any wire of three phases power source is broken off, this unit could cut off current to motor to prevent motor from being burn out.
*Drill sleeves、tapping adaptors and borer holder are with rapid adaptors, very convenient for replacement of cutters.
*Tapping adap....
The Spec Of Automatic Drilling Machines : *This model can use normal straight handle drill bit or oblique handle drill bit to drill holes. And use tap bit to tap thread.
*The drilling capacity is from 3mm-22mm and the tapping capacity is from 8mm-14mm.
*The up/down transmission of the tool bit is by the round shaft gear rack, so the drilled holes and the tap....
The Spec Of Automatic Drilling Machines : 1.Simultaneous double sides milling(length) + center drilling(drilling)(chamfer) for vehicle, motorcycle, vessel and agricultural machinery's engine, crank axle, motor spindle parts etc.
2.Optional auto feed device is available for manpower.
3.Working example: Bilaterial milling + drilling(chamfer).
The Spec Of Automatic Drilling Machines : *This model can use normal straight handle drill bit or oblique handle drill bit to drill holes. Furthermore it can also use annular cutter to cut holes.
*The drilling capacity is from 3mm-30mm and the cutting capacity is from 16mm-52mm.
*The up/down transmission of the tool bit is by the round shaft gear rack, so th....
The Spec Of Automatic Drilling Machines : *With circuit protection of breaking for motor, once any wire of three phases power source is broken off, this unit could cut off current to motor to prevent motor from being burn out.
*Drill sleeves、tapping adaptors and borer holder are all with rapid adaptors, very convenient for replacement of cutters.
*Tapping ....
The Spec Of Automatic Drilling Machines : 1. Standard spindle speeds 8,000 rpm
2. Optional spindle speeds 12,000 /15000 rpm
3. Rigid Tapping 3000 rpm
4. Spindle nose taper BT40
5. 3 axes rapid traverse X, Y, Z: 48 / 48 / 48 m/min
6. Fully enclosed heat isolated electric cabinet
7. High Speed Arm-type ATC time T-T: 2.4 sec
8. Directly coupled spindle dri....
The Spec Of Automatic Drilling Machines : 1. Standard spindle speeds 10,000 rpm
2. Optional spindle speeds 12,000 / 15,000 / 20,000 rpm / 24,000 rpm(Mitsubishi)
3. Rigid Tapping 4000 rpm
4. Spindle nose taper BT30
5. 3 axes rapid traverse X, Y, Z: 48 / 48 / 48 m/min
6. Fully enclosed heat isolated electric cabinet
7. High Speed Arm-type ATC time T-T: 2.2....
The Spec Of Automatic Drilling Machines : 1. Standard spindle speeds 8000 rpm
2. Optional spindle speeds 12,000 /15000 rpm
3. Rigid tapping 3000 rpm
4. Spindle nose taper BT40
5. 3 axes rapid traverse X, Y, Z: 48 / 48 / 48 m/min
6. Fully enclosed heat isolated electric cabinet
7. High Speed Arm-type ATC time T-T: 2.2 sec
8. Directly coupled spindle driv....
The Spec Of Automatic Drilling Machines : 1.Standard spindle speeds 10,000 rpm
2.Optional spindle speeds 12,000 / 15,000 / 20,000 rpm / 24,000 rpm (Mitsubishi)
3.Rigid tapping 4,000rpm
4.Spindle nose taper BT30 (STD)/BBT30 (OPT)
5.3 axes rapid traverse X, Y, Z: 48 / 48 / 60m/min
6.Fully enclosed heat isolated electric cabinet
7.High Speed mechanical ATC ....
The Spec Of Automatic Drilling Machines : ◾Spindle speed STD. 10000rpm
OPT. 12000rpm
15000rpm
20000rpm
24000rpm
◾Spindle motor M70V-B 5.5/3.7kw
0iMD 5.5/3.7kw
◾Rapid traverse X,Y,Z: 48/48/48 m/min
◾X axes travel 400mm
◾Y axes travel 500mm....
The Spec Of Automatic Drilling Machines : 1. Model: HC-316A.
2. Throat depth: 120 mm. 1. Drilling diameter: 6 mm.2. Paper thickness: 0.05-0.25 mm.3. Motor: 1/2 HP x 2.4. Machine dimensions (L x W x H): 950 x 860 x 1550 mm.5. Net weight: 460 kgs.6. Gross weight: 600 kgs. ....
